The Fundamentals of Plumbing Skills for Bathtub Installation
The Fundamentals of Plumbing Skills for Bathtub Installation
Blog Article
We have uncovered this post involving How to Install a Bathtub Yourself directly below on the net and think it made good sense to write about it with you on this page.
Mounting a bath tub isn't precisely rocket science, yet it does call for solid plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bath tub with a new one is likewise a moderately challenging task. If the old tub is readily obtainable, the project can move immediately; if you have to open up a wall surface to remove the old bathtub as well as position the brand-new bath tub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly need a helper to vacate the old tub as well as set in the brand-new one. Ensure you have actually qualified on your own for the work and also are comfortable attempting it. As opposed to employing a contractor to take over a halfway-completed job, it is much better to take into consideration utilizing one before you begin. Possibilities are you may require a specialist plumber to make tube connections.
This article will assist you install a new bathtub in your bathroom if you have actually already gotten a brand-new tub as well as don't need to transform the arrangement of your previous water pipelines.
Your tools and also material list should make up the following:
Preparing for the Installation
First of all, the supporting structure provided with the bathroom should be fitted (if called for) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to ensure that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps unit to prevent strain on the tub.
Fit the adaptable faucet connectors to the bottom of both taps using 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom must currently be ready to be suited its final position.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installment, then the first thing you must do is separate the water system. After doing so, activate the taps to drain any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite problematic because of the limited accessibility that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the faucets. Have a fabric all set for the continuing to be water that will certainly come from the pipes. Once the supply pipelines have actually been eliminated, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning during this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
Before going on to fit the new faucets, contrast the pipe connections on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Setting up the Bath tub
Using the two wooden boards under its feet, put the tub in the called for placement. The wood boards are valuable in uniformly spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The next goal is to ensure that the bathtub is leveled all round. This can be attained by examining the level as well as changing the feet on the bath tub up until the spirit level reads degree.
To set up taps, fit all-time low of the outermost versatile faucet port to the suitable supply pipeline by making a compression join; then do the very same for the other faucet.
Turn on the supply of water and also inspect all joints and brand-new pipework for leaks and also tighten them if essential. Fill up the bath tub and likewise examine the overflow electrical outlet and the regular electrical outlet for leaks.
Ultimately, take care of the bathroom paneling as described in the producer's instruction manual. Tiling and also sealing around the tub ought to wait until the bath tub has been made use of a minimum of when as this will certainly resolve it right into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to avoid damages to the string. One end of the port fits on the plastic tail of the faucet and also the various other end gives a link to the existing supply pipelines.
If you need to fit a monobloc, then you will call for reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin ensuring that the washing machines are in place in between the tap and also the sink. Protect the faucet in place with the maker given backnut. When the faucet is firmly in position, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical tap adapters. The former kind must be connected to the tap finishes first, tightening up just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bath satisfies the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture an inflexible seal, creating the water to pass through the wall surface in between the bathroom and also the tiling, bring about difficulties with wetness as well as possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your components as well as fittings. They are sold in tubes as well as cartridges, and are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bathtub with water before securing, to allow for the activity experienced when the bathtub is in use. The sealer can break relatively very early if you do not take into consideration this activity before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently available on the marketplace. It is recommended to fit the ceramic tiles using water-resistant or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that blog posting on Installing A Bathtub when doing a lookup on the search engines. Sharing is good. Helping others is fun. Many thanks for going through it.
Search-end for emergency plumbing. Report this page